ABS (acrylonitrile butadiene styrene) is a frequently used 3D printing material. It has good mechanical properties and can be used for a wide range of applications. Ultimaker ABS shows exceptionally low warping and consistent layer bonding, making it more reliable and easier to print with than other regular ABS filaments. Here is everything you need to know to start printing with Ultimaker ABS.
Always use the latest version of Cura and make sure that your 3D printer is updated with the latest firmware version to include the correct material profile for Ultimaker ABS.
ABS can be printed with a build plate temperature of 80 °C. Check the table below to find the temperatures per nozzle diameter for the best print results:
|Nozzle diameter (mm)||Nozzle temperature (°C)||Build plate temperature (°C)||Print cooling fan speed (%)|
The temperatures listed in the table are used for the Ultimaker ABS print profiles in Cura for the Ultimaker 2+ and Ultimaker 2 Extended+. For best results, it is crucial to select the right printer, nozzle diameter and material in Cura. Also, make sure to select the correct material on your Ultimaker 3D printer to automatically use the corresponding temperatures.
ABS requires some cooling while printing. However, too much cooling can cause problems with layer bonding. ABS tends to contract when cooling down too fast, leading to possible delamination. The default print cooling fan speed in Cura for the Ultimaker ABS depends on the nozzle diameter. The maximum print cooling fan speed is 100%, which means that shorter layers receive more cooling to retain an optimal print quality.
Cura Adhesion Settings
All default profiles for Ultimaker ABS in Cura use a brim as a build plate adhesion method. A brim is made of a few extra printed lines around the 3D print on the initial layer to ensure better adhesion and avoid warping.
When printing with Ultimaker ABS you must apply a thin layer of glue (included in the accessory box of your 3D printer) to the glass plate. Not using the glue results in a high risk of chipping the glass plate when removing the print and may void the warranty.
Please note that it may be easier to remove the 3D prints from the build plate if it is still slightly warm at approximately 40ºC.
For more tips on how to improve the build plate adhesion, see this page.
The Advanced 3D Printing Kit contains a package of special adhesion sheets as an alternative adhesion method to protect the glass plate. The door included in the kit will help avoid cracks in your 3D prints. This is especially important for large or thin-walled 3D prints. The door provides a controlled print environment for more consistent and reliable results.
Health and Safety
Ultimaker ABS is safe to print when using the recommended temperature settings listed above. To ensure a comfortable and healthy environment, we recommend 3D printing in a well-ventilated area.
For more information, download the safety data sheet for Ultimaker ABS here.
NOTE: The information provided here applies to Ultimaker ABS, but may apply to ABS filaments from other suppliers. The use of ABS from other suppliers is not covered by the Ultimaker warranty.
|Material Type||Acrylonitrile butadiene styrene|
|Weight on the spool||750 gr|
|Diameter tolerance||2.85 ± 0.10mm|
|Printing temperature||245 - 260°C|
|Melting temperature||225 - 245°C|
|Recommended temperature printbed||80°C|
|Recommended print speed|
|Tensile modulus||1681 MPa|
|Tensile stress at yield||39 MPa|
|Tensile stress at break||33.9 MPa|
|Elongation at yield||3.5%|
|Elongation at break||4.8%|
|Izod impact strength||/|
|Specific gravity||1.1 g/cc|
PLA (polylactic acid) is one of the most widely used 3D printing materials and also the recommended material for beginners. It prints fast, it is... View full product details
After ABS and PLA, Ultimaker has added a new material type to its gamma. The CPE line was created to print complex, technical prints. Comes... View full product details
Nylon (polyamide) is widely used by manufacturers to 3D print strong end-use parts and functional prototypes that require durability and abrasion resistance. Ultimaker Nylon is... View full product details
Highly versatile for industrial applications, TPU 95A filament is the go-to choice for a wide array of manufacturing projects that demand the qualities of... View full product details